Opticap <TMSYMBOL></TMSYMBOL> XL10 Polygard <TMSYMBOL></TMSYMBOL>-CN 0.3 μm 9/16 in.HB/HB

产品名称：

Opticap^® XL10 Polygard^® CN
Opticap XL10 Polygard -CN 0.3 m 9/16 in. HB/HB
Opticap XL10 Polygard -CN 0.3 μm 9/16 in.HB/HB

产品介绍：

产品说明

一般描述

Device Configuration: 取样皿滤膜

特点和优势

Format: Single Layer

包装

Double Easy-Open bag

其他说明

These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.
Directions for Use

Organism Retention: Microorganism reduction
Mode of Action: Filtration (size exclusion)
Application: BioProcessing
Intended Use: Reduction or removal of microorganism/bioburden
Instructions for Use: Please refer installation section of OPTICAP^® XL Capsules and OPTICAP^® XLT Capsules user guide
Storage Statement: Store in dry location
Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

联系

Replaces: KN0301HB1

制备说明

Sterilization Method
3 autoclave cycles of 30 min @ 126 °C; not in-line steam sterilizable

分析说明

Gravimetric Extractables: after 24 hours in water at controlled room temperature
Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥5 L

法律信息

OPTICAP is a registered trademark of Merck KGaA, Darmstadt, Germany
POLYGARD is a registered trademark of Merck KGaA, Darmstadt, Germany

免责声明

EMD Millipore Corporation certifies that this product complies with the European Pressure Equipment Directive, 97/23/EC of 29 May 1997. This product has been classified under Article 3 § 3 of the Pressure Vessel Directive. It has been designed and manufactured in accordance with sound engineering practice to ensure safe use. In compliance with Article 3 § 3 of this Pressure Vessel Directive, this product does not bear the CE mark.

基本信息

eCl@ss

32031690

产品性质

质量水平	400
物料	polypropylene polypropylene housing polypropylene support polypropylene vent cap silicone seal
reg. compliance	meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
manufacturer/tradename	Opticap^®
参数	1.0 bar max. inlet pressure (15 psi) at 80 ℃ 2.75 bar max. inlet pressure (40 psi) at 60 ℃ 25 ℃ max. inlet temp. 4.8 bar max. differential pressure (70 psid) at 20 ℃ 5.5 bar max. inlet pressure (80 psi) at 25 ℃ 80 psig max. inlet pressure
长度	33.5 cm (13.2 in.)
cartridge nominal length	10 in. (25 cm)
直径	10.7 cm (4.2 in.)
过滤面积	0.42 m²
inlet connection diam.	9/16 in.
inlet to outlet W	33.5 cm (13.2 in.)
outlet connection diam.	9/16 in.
总尺寸	10 in.
杂质	≤0.5 EU/mL bacterial endotoxins (LAL test, Aqueous extraction) <0.5 EU/mL USP bacterial endotoxins (LAL test, sample aqueous extraction)
gravimetric extractables	≤55 mg/capsule
基质	Polygard^®-CN
孔径	0.3 μm nominal pore size 0.3 μm pore size
input	sample type liquid
配件	inlet hose barb 14 mm (9/16 in.) inlet/outlet hose barb outlet hose barb

Opticap® XL10 Polygard® CN

Opticap^® XL10 Polygard^® CN